Haier Washer HWM80 828A User Manual

Specification table  
Water level/Water  
1/15L 2/21L 3/27L 4/33L 5/37L 6/41L 7/46L 8/52L  
quantity (about)  
Water Injection pressure  
Washing / spinning capacity  
0.03MPa  
1.0MPa  
-
8.0kg/8.0kg  
Full Automatic Washing Machine  
User's manual  
This manual is for  
HWM80-828A  
WARRANTY:  
Please read this manual  
Two years free for motor  
One year free for other parts  
carefully before using.  
0030508582B  
Retain it for future reference.  
 
Names of the parts  
Trouble-shooting answer to question  
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns  
sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.  
Phenomena  
The reason  
How to settle  
Close the top lid.  
The digitron displays E0.  
The top lid is opened during reserve procedure.  
The drainage cannot work, or is too slow.  
The digitron displays E1.  
Is the drain hose put down?  
Is the drain hose blocked?  
Put down the drain hose. Open and close the top lid once.  
Clean the foreign material. Open and close The top Lid Once.  
It stops running in midway. The digitron  
displays E2.  
The top lid is not closed.  
Close the top lid.  
The safety switch acts, and the  
spinning cannot work. The  
digitron displays E3.  
Are the laundries put slantingly?  
Is the machine slanting?  
Reorder the laundries. Close the top lid.  
Th machine will start running after 10  
seconds of being placed horizontally.  
Open the water tap. Push the start/Pause  
button once.  
Clean the water inlet valve then push  
the Start/Pause button once.  
Push the Start/Pause button once.  
Is the water tap opened, or is there water  
supply failure?  
Is the water inlet valve blocked?  
Is the water pressure too low?  
The water filling does not work,  
the digital displays E4.  
Please contact the after-sales  
service department.  
The digitron displays E6.  
The water level sensor is bad.  
Is there power failure?  
Is the power plug inserted tightly?  
Is the water level reached preset position?  
Please use it when there's power supply.  
Insert the power plug tightly.  
Fill water to the preset position.  
Not wash  
The machine does  
not act  
Is the power plug inserted tightly?  
Is the top lid closed reliably?  
Are the laundries set flat?  
Insert the power plug tightly.  
Close the top lid.  
Set the laundries flat.  
Not spin  
Meaning and description of the symbols  
Warning sign  
Adjust the machine to be even  
Reorder the laundries and close the top lid.  
Remove the foreign materials.  
Is the machine slanting?  
Are the laundries put slantingly in spinning?  
Are there any foreign materials?  
There's abnormal sound  
inside the machine  
Is the screw of the jointer of water  
inlet hose loose or awry?  
Fasten the screw of the jointer properly.  
Contents marked with that symbol are related to the  
The water tap leaks  
safety of the product and the personal safety of the users.  
Please operate in strict conformity to the contents.  
Common phenomena  
Phenomena  
Explanation  
Balance the laundries to avoid slanting.  
The spinning is intermittent when it starts.  
The wash procedure is paused.  
Forbidden sign  
Contents marked with that symbol are actions forbidden  
to perform. Performing of those action may result in damage of  
the machine or influence the personal safety of the users.  
The cloth sensor is checking the cloth, it willadd waterafter 48 seconds.  
The program is setting the drain time. Some time is needed  
before it starts spinning.  
Push the PROGRAM button to select SPIN,  
but it doesn't work.  
The pulsator pauses during water inlet  
in wash and rinse.  
It is to avoid splashing during water inlet.  
There may be some water flowing out of the  
drain hose in the first use of the machine.  
It is the water remained in the factory inspection of performance.  
16  
1
 
Safety precautions  
Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter etc. in time.  
Otherwise it may influence your using the machine.  
The washing machinemust be positioned sothat  
Please plug the power plug on special  
receptacle. Be sure to use three-pins  
power receptacle. Ensure that the earthing  
prong of the power receptacle is earthed  
reliably. Use leakage protector if possible.  
the plug is accessible.Be sure topull the plugoff  
and close thewater faucet infollowing cases:  
power failure, deliveringthe machine, settingthe  
machine idle orcleaning the machine.Do not plug  
or pull thepower plug withwet hand.  
Please first pull off the power plug from the receptacle before cleaning.  
The lint filter must be used during washing.  
Clean the detergent box and set it on  
It must be cleaned in time after each using.  
the control panel seat.  
Lint filter:  
1.The method of dismantle: Push it up aslant and gently.  
2.The method of install : install it upwards and aslant  
and push it in .  
1.Push down the spring piece of the top lint filter  
to make the claws out of the filter cover, and then  
pull out the lint filter to get it down. figure1  
2.Pull the back of the lint filter, and then you can  
get down it off the front cover of the lint filter. figure2  
3.Sweep the rubbish in the lint filter.  
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.  
Keep the pin of the power plug clean, if the power plug is polluted with dust, please wipe with  
dry cloth carefully.  
If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by  
the technicians of our special shop or our customer care agent.  
4.Put the back of the lint filter into the front cover .  
5.Put the lint filter into filter cover, and make it  
tight .  
6.Make sure the lint filter well installed, or it can  
influence your use.  
In case the washing machine is installed on ground with  
carpet, do not block the ventilation hole with carpet.  
Do not use water hotter than 50  
.
Dismantle  
Install  
The back cover of lint filter  
Up  
Up  
The ventilation  
holes at the bottom  
Dismantle  
Dismantle  
Install  
C
0
5
Install  
Down  
Carpet  
The front cover of lint filter  
Figure 2  
Down  
Figure 1  
The filter screen of the water inlet valve is likely to be  
blocked by foreign materials and influence the water  
inlet.  
If the cabinet is dirty, wipe it with wet cloth  
Do not flush it directly with water.  
Do not put the machine at damp place like  
the bathroom. Never wash it with water. Do  
not put wet laundries on the control panel.  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations in spinning.  
Please clean it with brush every two months.  
Wipe it with neutral detergent.  
Do not wipe it with thinner, petrol, alcohol etc.  
rol  
Pet  
r
ne  
in  
Th  
Alcohol  
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).  
Do not let the machine share one receptacle with other  
electric appliances. If the plugging into the receptacle  
is loose, do not use the plug any more.  
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.  
3.Be sure to pull off the power plug before maintenance.  
4.Hang up the power cord and drain hose.  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time  
(about 1 hour), then close the top lid.  
15  
2
 
Safety precautions  
The washing machine has a Wool program , intended for high-grade fabrics such as cashmere . First, make sure the laundry  
can be washed with water or not. If not, do not use the washing machine to wash the laundry. If yes, select the washing cycle  
recommended by the fabric man ufacturer. The Woollen program can be used to wash fine clothes such as cashmere sweater,  
linen blouse,woolen pants; For clothes with local stains, such as sticky stains at collar or cuff, lay the clothes upon a towel and  
spread neutral detergent (for washing machine) on the stains. Use a soft brush to pat at the clothes gently before putting the  
clothes into the machine.Do not rub the clothes hard.  
Do not put hand into the rotating tub. It is dangerous  
even if the rotation speed is slow. Take special care of  
the children. Keep children away from the washing  
machine to avoid them climbing on.  
Do not decompose, repair or alter the machine by  
yourself.  
Before washing, please fold up the laundry as needed, then put the laundry into the inner tub, flat and neat.  
These fabrics are not washable:  
1. Fabrics that deform when soaked in water;  
2.Fabrics that shrink, discolor or go through other exterior changes when soaked in water;  
3.Fabrics that lose original texture when soaked in water;  
4.Fabrics that discolor when soaked in water;  
5.Fabrics that have pilling or pressed pile when soaked in water;  
6.Fabrics that have damage when soaked in water.  
Do not put any hot or heavy items (such as the  
kettle with hot water) on the washing machine.  
Do not wash laundries with volatile materials  
(such as thinner, petrol etc.).  
Upon completion of washing, iron the laundry with a steam iron.  
When shrinkage occurs  
Hold the steam iron above  
Stretch the laundry toits original  
size and locate itwith pins. Use  
the laundry. Reshape the  
rol  
the laundry and do not touch  
Pet  
Benzene  
a steam iron todry the laundry  
completely. Donot touch the  
laundry. (Asillustrated in Fig 2)  
laundry. (As illustrated  
in Fig 1)  
Pin  
Figure 2  
Figure 1  
3 Push "SOAK" "WASH" "RINSE" "SPIN" button to select suitable procedure program  
Even there's no water in the tub, a certain period is required before spin starting.  
Separate the laundries that are not colorfast from other laundries in washing.  
The soak procedure can work in cooperation with automatic programs like MEMORY,BLANKET, STANDARD, CHILD,  
COMMON. There is intermittent pulsator stirring during soak.  
Keep the machine away from direct sunlight and  
heat source like the heater.  
The handicapped or children without care shall not use  
the machine.  
After the machine starts operation, you can only set the program and procedure during washing and soaking,  
During rinsing you can only set the spinning time. and can not make setting in other cases.  
During speedy and tub dry programs. push the wash ,rinse spin button the machine have no reaction.  
4 Push the " WATER LEVEL "button, select suitable water level  
For program, the washing machine will execute fuzzy program automatically to detect the cloth.  
After defection, it can set the water level automatically. To select other water level, first push the "START/PAUSE"  
button, then push the "WATER LEVEL" button to set the water level.  
5 Push the "DELAY" button to select suitable reserve wash program  
Please keep the lint filter in good condition,  
and install it to proper position during  
To protect your laundries and washing machine,  
please take out all of the coins, buttons, sand, hairpin  
and other foreign materials before washing.  
After switching on the power, the reserve program is set to off mode automatically. If you need to  
set the washing procedure to be finished at reserved time, please push the "DELAY " button to  
set the reserve wash program. Refer to reserve button in Page 12 for selection.  
washing. If the lint filter is lost or  
Install  
Dismantle  
damaged, please contact the customer  
care agent of our company.  
P12  
When the "DELAY" function is activated, the indicator light of the program you  
have set will be off. The "reserve (hour)" and "time remain" indicator lights will  
be on. During reserve procedure, push the "DELAY" button to display the reserve mode.  
To change the running program or cancel the reserve setting, you  
.
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.  
It is suggested to use foamless washing powder.  
need to switch off the power and make new selection.  
To change the direction of drain pipe, please contact the customer care agent of our company.  
6 Push the "START/PAUSE" button  
Please don t use the washer in the environment below 0 C; if the washer has been stored below 0 C,  
please be sure to ensure the washer is placed under the room temperature for 24 hours and then use  
otherwise the washing effects may be lowered or the washer may be damaged.  
6 Finish washing  
After finishing wash it'll alarm and switch off power automatically  
134  
3
 
Installation and adjustment  
Please install and adjust the machine according to the requirement of the manual.  
It is very important to your security and correct operating the machine.  
I
"DELAY " button  
Press the "DELAY" button, digital display the time of washing appointment  
(by the hour display), LED starts blinking. In hours, an appointment can choose between 2-24 hours,  
for a long time press by "DELAY" button, the time of appointment can be continuously increased.  
Appointment process, press the "DELAY" button to display reservation status.  
Install the inner cover component  
1.Open the top lid of the washing machine.  
J
"SOAK " button  
2.Put the inner cover component on the outer tub cover, aiming the inner cover  
shaft to the installation hole of the corresponding outer tub cover shaft groove.  
3.Firstly insert the inner cover shaft of one side into the corresponding outer tub  
cover shaft groove, then push the another inner cover shaft into the corresponding outer  
tub cover shaft groove. Please install to designated position to guarantee there are no  
dropping or abnormal sound in opening and closing of the inner cover, and the operation  
shall be smooth. Do not dismount the inner cover component after washing.  
Outer tub cover  
For the MEMORY,BLANKET,JCHILD,STANDARD programs push the SOAK botton to  
select the desired soak time( 10, 20,30,40 minutes)  
SOAK  
The button isunavailable from theSPEEDY SILK andWOOL programs.  
K Reserve, remain time digitron  
It displays "--" during detecting.  
Right hand  
Outer tub cover shaft groove  
It displays remained reserve time (hour).  
It displays abnormal symbol in abnormal situation.(See to Page16)  
Inner cover shaft  
Left hand  
Inner cover component  
Figure 2  
Figure 1  
L
"RESERVE WATER " button  
You can choose "RESERVE WATER" function to keep the after rinsing water.  
Washing machine will keep the after rinsing water once finish rinsing in tub about 4 hours, and buzzer every 15  
minutes.( For example, if you choose "SECOND RINSE", the machine only keep the after second rinsing water,  
if you choose "FIRST RINSE" and "SECOND RINSE" together, the machine will keep the after first and second  
rinsing water)  
RESERVE  
WATER  
Install the bottom plate  
Press"START/PAUSE" button or open and close the top lid one time to collect the after rinsing water, then the  
machine will go on for next program.  
If you don't collect the after rinsing water within 4 hours, the machine will drain automaticly, then go on for  
next program.  
After you open the package, please lean  
the washing machine gently down on soft  
items ( like the towel cloth, blanket, etc. ).  
Install the bottom plate to the bottom of  
the machine, then lift the machine up  
gently. See to the figure:  
I
Back  
Steps of using the operation buttons and description of the  
steps  
1.Push "POWER" button to switch on the power  
Front  
Bottom plate  
Soft items  
2.Push "PROGRAM/" button to select suitable full-auto program  
Section I enlarging  
Two claws at the bottom cover shall  
be inserted in two bar-shaped holes  
in the stand. Make sure the claws  
are firmly in place.  
After the power is switched on, "MEMORY" is automatically set. To select other full-auto program, please push  
the "PROGRAM" button till the corresponding indicator is on. Refer to the "PROGRAM" button on Page 10.  
E.g. Set to "SPEEDY"program for small quantity of laundries with light soil.  
When a standard cycle is selected, the fuzzy program is run. The water level and the washing time can be  
selected according to be texture and volume of the laundry. The washing cycle is automatically controlled.  
13  
4
 
"WASH " button  
Adjust the Installation position  
Press the Wash button toselect a wash time, from the MEMORY,BLANKET, CHILD ,SPEEDY, STANDARD  
programs.  
WASH  
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground will result in  
unstable running or stoppage of the machine. Please adjust it with following methods:  
Press the Wash button can select or cancel the process of wash ,but can not change time from  
the SILK programs.  
The button is unavailable from the SPEEDY and WOOL programs.  
Confirm it's horizontal:  
Hang the lead line to check if it is  
horizontal.  
E "SPIN " button  
Press the "SPIN "button to selectspin time, fromthe MEMORY,BLANKET,JEAN,STANDARD program.  
The button isunavailable from theSPEEDY and WOOL programs.  
<2  
SPIN  
Adjust the adjustable leg:  
Press "SPIN"buttoncan select orcancel the processof spin ,butcan not change time  
from the SILKprograms.  
1 .To twist the adjustable leg, please first lift up the  
side of the leg slightly, loosen the adjustable nut,  
the adjustable nut  
and twist the leg.  
Fasten  
Loosen  
High  
the adjustable leg  
Low  
F "WATER LEVEL"button  
2 . After adjustment, fasten the nut.  
Common, memory and standardprocedures for washing machineautomatically detects the amountof cloth,  
the water level isautomatically set to 4.6.8in an appropriate level.Into the wet clothing,may be set to"8" level,  
the user needs tochoose the appropriate level.  
Usage the drain hose  
Due to differentlevels of wet anddry cloth to determinethe actual water levelmay be different;  
WATER  
LEVEL  
The drainage shall be smooth with the drain hose.  
Washing machines beganto work, to manuallychange the level, pressthe "start pause" buttonre-select.  
1.The height of the drain hose shall be less than  
10cm, or the drainage will not be smooth, and  
cost such long time that the machine may stop  
at mid way.  
If there's water inside the tub, the machine cannot detect the laundries and will display water level 6 .  
4.If extra drain hose is needed, please make  
separate purchase. The inner diameter of the  
extra hose shall not less than 30mm, and the  
length shall not exceed 1.5m.  
During the period of "washing" and "rinse", holddown the "water" buttonfill water, handrelease or overflow water  
to stop when reachedthe water level.  
Wool, silk programlevel only can bechoosen between 4-8 level,blanket water level ofthe program to  
select between 2-5  
In common, strong, children,standards, and the memoryprocess, the rinse waterwhen washing the waterlevel  
higher than that ofa file (the highestwater level and artificialselection, except when rinsewater)  
2.Do not step on or press the drain hose.  
>
30mm  
G "AIR DRY"button  
<10cm  
<1.5m  
Push the "AIRDRY" button to select air dryprocedure. The program ischosen(0.5h 1.0h 2.0h).  
0.5 1.0h The purposeis drying the inner tub and the outer tub, which can avoid growing  
mildew on the outer tub andthe inner tub.  
AIR DRY  
3. If the drain hose is too long, cut it at mid point.  
To make smooth drainage, cut the front end of  
the hose slantingly.  
5.If the extra hose is too long, cut it either at A  
or at B.  
2.0h can dry laundries The max drying capacity of the fibre laundrie is 2.0 kg.  
"AIR DRY"program cannot be reserved  
H "RINSE"button  
For the MEMORY,BLANKET,CHILD,STANDARD programs push the RINSE botton  
then push select the rinse times Overflow rinse.1.2.3.  
light is flashing ,  
RINSE  
For ECONOMY ,WOOL programs, press "RINSE"button can not change time  
B
A
The button isunavailable from theSPEEDY and TUB DRY programs.  
1123  
5
 
5 Use the operation button  
How to change the direction of the drain hose  
Description of operation button  
POWER  
ON/OFF  
REMAIN(MINUTES)  
20  
15  
10  
5
40  
30  
20  
10  
STANDARD  
MEMORY  
COMMON  
BLANKET  
8
6
4
7
5
3
FIRST RINSE  
9
7
5
3
3
2
1.Lean the machine down gently with the front  
4.Put your hand into the machine and loosen the  
SECOND RINSE  
THIRD RINSE  
surface facing the ground. as indicated in Figure 1  
clip of drain pipe support then pull inside the pipe  
and fetch out from the other side and set it on the  
CHILD  
WOOL  
SILK  
START  
PAUSE  
1
SPEEDY  
RESERVER(HOURS)  
DELAY  
1
2
OVERFLOW  
clip, as indicated in Figure 3.  
2.Dismantle the rear cover of the washing machine.  
as indicated in Figure 2  
RESERVE  
WATER  
AIR DRY  
WATER  
LEVEL  
SOAK  
WASH  
RINSE  
SPIN  
5.Install Hook of fixing the drain hose and bottom  
cover then lift the machine up gently.  
3.Pinch the mouth of drain pipe and take off the  
pipe hook.  
Indicator mode and meaning  
Off  
Flashing, indicating the running program  
On, indicating the program about to run or the selection mode  
Unhinge clamp  
outlet  
Child lock function  
The function is intended for children safety and preventing the washing programfrom accidental changes by children.  
Figure 2  
Figure 1  
Figure 3  
Push and hold the water level button and spinbutton, then pushdown the poweron/off button .  
You cancontinue setting desired washing procedures. After setting ,pushdown the start/pausebutton. The  
child lock function is activated. all of the buttonsare locked and cannot make selection .  
Release the child lock function :push down water levelbutton and spinbutton at thesame time for more 2seconds .  
After a beepsound ,the child lock function is released.  
Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of  
the drain hose with our company serviceman .  
A "POWER" button  
Push the "POWER" button to switch on the power.  
POWER  
Under power-on mode, push it to switch off the power.  
ON/OFF  
Push the "POWER" button to switch on the power. If the "START/PAUSE" button is not pushed, the machine will  
switch off the power automatically after 5 minutes.  
B "START/PAUSE" button  
START  
PAUSE  
After the poweris switched on, press it to start the machine  
During working, push it to pause.  
During pause, pushthis button torestart and goon working  
C "PROGRAM" button  
Program  
Application  
Program  
Application  
COMMON  
STANDARD Standard saving washing for normal laundries  
Washing the common laundries  
The commom wash , the washing machine  
PROGRAM  
will set to MEMORY program including  
"wash, rinse,spin,water value "automatically  
last time  
BLANKET  
MEMORY  
Washing the relatively big and thick laundries  
Washing the relatively big and thick laundries  
Quick washing for normal laundries  
JEAN  
Washing for the woollen laundries, under 2.5kg  
Washing the silk laundries  
WOOL  
SILK  
SPEEDY  
6
11  
 
Install the water inlet hose  
Put in the laundries  
Confirm the water faucet  
The capacity of washing of the machine refer to the largest weight of the  
standard laundries under dry condition that can be washed in one  
time. Laundries quantity in one washing cycle shall be lower than  
the standard capacity.  
Water faucet,suitable  
Water faucet,not suitable  
The thickness ,size , type of the cloth will influence the actual washing capacity.  
It is suitable to put in reasonable amount of laundries and the laundries can be turned  
round in washing for one time washing.  
Outlet end surface  
Do not select " 4" water level for laundries less than 1.0kg ,so as to avoid  
splashing of water.  
>10mm  
It is required that the front end shall be longer than 10mm.  
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.  
How to use the softner  
The usage and dose of the softener as per the specifications of softener.  
Before washing put the softener into the detergent box directly as  
3 Usage of detergent  
indicated in the left figure The softener will put into the washer  
when the last rinsing.  
After that,please close the detergent box Refer to the following list for  
the usage of the detergent:selection of the water level,water quantity  
and dosage of detergent  
Connection between the water inlet hose jointer and the water faucet  
Control panel seat  
Liquid detergent inlet  
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the  
water inlet hose component. See to Figure 1.  
After the softener is put in, please don't place for a long time otherwise  
softener may solidify and cause flowing not smooth.  
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.  
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen  
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,  
otherwise it may leak water. See to Figure 3.)  
Access for detergent and washing powder  
Access for softener  
How to use washing powder  
water inlet hose jointer  
It is suggested to add washing powder into the box  
directly under fuzzy program and reserve program.  
Screw  
Detergent box  
Slider  
Dissolve directly inside the washing machine: (not  
applicable for fuzzy and reserve program)  
1.Add some water(select " 1 " water level).  
Sign plate  
Screw knife  
Bushing  
Figure 3  
Lock level  
2.Add washing powder. Run for about 30s to fully dissolve  
Powder. Then push the"START/PAUSE" button.  
the  
3.Put in laundries. Select suitable water level. Push the  
water inlet hose  
Figure 2  
Figure 1  
Button again.  
"START/PAUSE"  
How to use whitener  
Quick dissolving of washing powder:  
1.Prepare warm water of 30 C and container.  
2. Add washing powder while stirring to dissolve it completely.  
3.Fasten the four screws evenly. See to Figure 4.  
Add water to stipulated level. Dilute the whitener with container,  
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure  
to seal up the exit end face of the faucet. See to Figure 5.  
and then pour it into the liquid whitener inlet slowly.  
Laundries with color or pattern is not colorfast, thus not applicable.  
Please add suitable washing powder as per the laundries  
quantity, the set water level and water quantity.  
If you select "Speedy" program, it is suggested to use  
liquid detergent instead of washing powder to guarantee  
the washing effect.  
The whitener shall not touch laundries directly.  
See to the manual of whitener for the usage and dosage.  
For whitener in powder, dissolve it before use.  
remark: Before installation, the threading is 4mmabove the upper surface of the nut.  
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.  
It is not recommended to use rich-foam washing powder.  
Washing powder with poor quality or long-time storage may  
get caked. Please clean the detergent box duly in usage.  
About 4mm before twisting  
About less than 2mm after twisting  
Screw nut  
Figure 5  
4 Close the top lid  
Figure 4  
Figure 6  
As the top lid opened, the washer will automatically given alarm and stop running, exclusively during draining.  
10  
7
 
1 Preparation before washing  
Connection between the water inlet hose and the washer  
Preparation before washing  
1.Connect the water inlet hose.  
1.Do not take off the water absorption cushion. Please check if the  
2.Confirm that the washing machine is earthed  
reliably. Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose.  
nut of the water  
cushion is dropped or damaged before each usage. If it happens  
inlet hose  
please contact our after-sale department immediately.  
2 .Put the nut of the water inlet hose on the valve jointer.  
3 .Fasten the nut. Swing it gently to confirm if it's suitable.  
jointer of the  
water inlet valve  
water absorption  
cushion.  
Connection between the jointer of the water inlet hose and the water inlet hose  
4.Slanting or uneven ground may result in  
unstable working or abnormal noise. Please  
make the machine stand horizontally.  
1.Push down the slider. Insert the water inlet hose into the jointer.  
the jointer of the  
water inlet hose  
Locking level  
Slider  
2 Hang the lock lever to the jointer. Release the slider till a click  
sound is heard.  
Pay attention to followings before washing the laundries  
Check the connection between the jointer of the water inlet hose  
and the water faucet  
Clear the pocket.  
Take out the coins ,  
sand, hairpins etc.  
Confirm if there's  
special requirement  
for the laundries.  
The quantity of the  
laundries shall not  
exceed the rated  
value. The big  
laundries like the  
jeans shall be put  
in loosely.  
Fasten the buttons  
and zippers.  
When the pulsator is  
running ,the buttons of  
the laundries may cause  
noise. For the sake of  
discretion ,please put  
the laundries with  
buttons into other  
1.Swing the hose gently to confirm if it is fastened stable.  
2.After installation, open the faucet to check if it leaks.  
3.Do not bend the hose with overstrain.  
4.Before each usage please check if the connection  
between the jointer of the water inlet hose and the  
water faucet, and the installation of the water inlet  
hose are firm, so as to prevent dropping from  
improper installation position.  
laundries.  
Dismantle the water inlet hose  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries with unfast color from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
1. Close the water faucet.  
2. Press the locking lever. Push down the slider. Then pull of the water inlet  
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,  
please apply detergent in advance, which can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.  
f. Do not put those laundries polluted by chemicals directly into the washing machine.  
g. For those small laundries and those may get twisting or worn, and woollen/fur laundries, please put them into  
mesh bag for washing.  
hose.  
Locking level  
If the machine is used frequently, the jointer of the water inlet hose can be  
Slider  
on the faucet to prevent damaging the fixing screw.  
kept  
8
9
 

Greenheck Fan Fan LFC User Manual
Grizzly Lathe G0740 User Manual
Grizzly Sander G9984 G9985 User Manual
Hans Grohe Indoor Furnishings 31100XX1 User Manual
Harbor Freight Tools TV Mount 68784 User Manual
Hotpoint Oven SX 896L PX User Manual
HP Hewlett Packard Laptop 333953 001 User Manual
HP Hewlett Packard Welder ML 150 G3 User Manual
Husqvarna Snow Blower 1330SBEXP User Manual
Husqvarna Trimmer 325R User Manual